Electronics Products

The RLM is a dry film laminator especially made for small companies, schools, research and development departments. All commercial laminates for PCB manufacture and mould-etching technique can be processed. Due to adjustable pressure control and adjustable laminating speed, solder mask application is also possible without problems. The machine is also used very successfully in other application fields like WAFER MASKING and SMT STENCIL production or METAL WORKING.

Features:

• Easy and fast mounting of resist rollers of all common coil diameters

• Detachable inlet table for easy access to lower resist roll

• Infinitely adjustable laminating speed

• Electrically heated laminating rollers with uniform temperature distribution

• Separate transport rollers for non-creasing laminate transport

• Digital setting and read out of lamination temperature

• Manually adjustable lamination pressure

• For all common dry fi lm resists with 3 and 5 inch core diameter

• Suitable for solder mask application

Technical data:

This high performance multilayer press was designed for PCB labs to enable quick prototyping of multilayer PCBs according to industry standards. HNumber of layers is only limited by the maximum lift of the press plates (38 mm). Using separating metal sheets one can press a couple of boards over each other at the same time. A compact and floor standing aluminum rack contains all parts of the unit including pressure supply, press plates and heaters. The large loading door allows quick and easy access to the press chamber and is of course security switch protected. A compressor, which is an integral part of RMP 210 / RMP 3545 is stored in the back of the machine. In the front, you will find additional storage room for tools or boards (lower door). The unit is controlled by two digital and adjustable thermostats, one digital timer as well as a pressure valve with a pressure meter. Four strong air ventilators are activated automatically during cooling cycle.

Features:

Steps of multilayer production:

• Boards are pinned and stack is inserted into press plates.

• Pressure is created.

• Heater is activated.

• Heating up procedure.

• Press procedure at preset temperature.

• Cooling down under pressure.

• PCB stack is taken out of the machine.

 Vacuum options:

Technical data:

Spray etching machine for laboratory use with integrated static rinse. Machine is suitable for double sided material. Special emphasis was put on ergonomical and clean etching and rinsing as well as on low chemical drag out.

Features:

• Maintenance free system with self-cleaning nozzles and magnetic pump
• Etching speed of 35 μm Cu within 90 seconds (warm Fe-III-Cl).
• Big window to the etching chamber made from transparent PVC.
• Maximum board size: 210 x 300 mm. (Splash XL: 300 x 400 mm)
• Line resolution better than 0.1 mm (100 μm)
• Suitable for all common etchants
• Lid to the etching chamber with safety switch
• Removable board holder made from Titanium and PVC. Can be locked in drip-off position
• Easy access to the etching chamber.
• Strong 1000 W Quarz heater, controlled by thermostat
• Overheat fuse
• Digital timer with count down, auto reset and beeper.
• Integrated rinsing zone with drip off holder.
• 3 cog valves for all tanks
• Suitable for spray developing

Technical data:

Laboratory etching machine with static and spray rinse, integrated developer tank, a reserve tank for e.g. chemical tinning and a squeeze dryer. The Splash-Center is suitable for double-sided PCBs. Special emphasis was put on ergonomical and clean etching and rinsing as well as on low chemical drag out. A typical workflow for example is to use tank 1 (spray compartment) for etching, tank 2 and 3 for rinsing, tank 4 (with centrifugal pump) for developing and tank 5 for tinning.

Etching Compartment:

• Maintenance free etching system with solid stream nozzles
• Etching speed of 35 µm Cu within 90 seconds (warm Fe-III-Cl).
• Big window to the etching chamber made from transparent PVC.
• Maximum board size: 210 x 300 mm /Splash-Center XL: 300 x 400
• Line resolution better than 0.1 mm (100 µm)
• Suitable for all common etchants. Fe-III-Cl recommended
• Lid to the etching chamber with safety switch
• Removable board holder made from Titanium and PVC. Can be locked in drip-off position
• Easy access to the etching chamber.
• Strong 1000 W Quartz heater, etching temperature controlled by thermostat
• Overheat fuse
• Digital timer with countdown, auto reset and beeper
• Integrated rinsing zone with drip off holder.
• 5 ball valves for all tanks
• Suitable for spray developing

Developer and rinse compartment:

• Magnetic centrifugal pump to revolve developer
• two integrated static rinses, one can be used for neutralization purposes
• Fresh water spray zone activated by foot switch, including splash protection
• A reserve tank, e.g. for immersion tin

Features:

• 5 ball valves to drain all tanks, cover protected from the front side.
• All tanks with lids
• Integrated drip tray for all tanks, sure-footed about 120 mm above the ground
• Integrated mechanical squeeze dryer

Technical data:

VARIODRILL is a PCB drilling machine for prototypes and small batch production. The demand for operating comfort and high quality has led to an untraditional design which meets the necessary requirements for an ergonomic correct working position.

Features:

• comfortable working position, drill table can be tilted up to 30 °
• magnifier optics directly over the drill hole (parallaxes free)
• Illuminated work area
• Motor controlled, adjustable stroke speed, spindle underneath the table
• AC Motor, 100 Watts / 230 Volt
• Including foot switch for easy operating
• Booth hands are free for positioning the PCB
• Complete system with integral dust extraction
• Including external vacuum cleaner
• Throat depth: 115 mm, max. board size 230 mm x endless
• Chuck: 1/8" (3.175 mm)
• Drill size 0.6 to 3.2 mm

Technical data: